Motherboard

On this page, I will be discussing the population and placement of the most important component of the unit. First and most important, STATIC ELECTRICITY!

Wherever you may be touching the motherboard, make sure you are grounded. You will note that most of your components arrive in a black static electricity bag. Therefore when you remove this from its bag, unless you have a grounding mat be sure to set the ATX, AMD motherboard on the bag. If you don’t try and keep the motherboard from the exposure to static, it may or may not get zapped. Like I said earlier why to take the chance when it could kill the board.

5% OFF for Computers & Networking(Code:COMPUTERS6)
Installing the PCB (printed circuit board) into the chassis can be done in two ways. First of all, this is going to be your third step in the process.

You may install the PCB (motherboard) directly into the chassis, or you may install some of its components on the PCB first. In my experience, I have found it easier to install some of the components first.

  1. Place the PCB on top of the static bag, as the face is facing to the left of you.
  2. Unpack the AMD processor, You will be installing this AMD am3 processor into the motherboards am3 socket. NOTE: polarity on the AMD processor and the PCB motherboard socket. Also be sure to raise the arm on the socket first, then once you got it in place pull the arm down and lock it in place.
  3. Using the standard heat sink that comes with the processor, there should be some compound on the bottom of it. Try very hard not to misaligned the heatsink/fan to the processor. This is pretty important to have the processor evenly cover and smooth. Don’t panic if you don’t get it the first time. Simply take and old credit card or something like that to smooth it out. Try not to loose too much of the thermal compound, if so you may purchase some at the time you purchase your parts or maybe your friends or family may have some left over.  Line up the arms that clamp down over the processor on both sides, once you got them in place just pull the arms down to tighten. Once again while you are doing this be sure to hold it in place so it doesn’t slide off.
  4. Now we are going to be installing the memory into the printed circuit board. You will notice that on the PCB that there are two connectors for the memory chips. See the middle or almost middle that there is a separator between the two and on the ends they have like little ears or clips that you will be pushing in to hold the memory chips in. These memory chips will only go in one way, one end is longer than the other to the separator.

Copyrighted.com Registered & Protected BJ3Q-UOGF-W0CW-HICS

6 thoughts on “Motherboard”

  1. Hi there! Your site is intriguing. Just for the simple fact that I’ve never considered building my own computer! So how many have you built? Can you sell any that you’ve built? I hate getting shocked. Any chance of that happening? Or does the motherboard just get zapped if you’re not careful with being grounded?

    • 1. I have built quite a few mainly I have repair them.

      2. Yes I can sell them.

      3. The more in getting shocked won’t be you feeling it, it will definitely ruin the motherboard. in what is awful with that scenario you won’t know until you’re done building it. My goal here was to have people build their own. I do enjoy building them, just the accomplishment to having the ability to do it. I guess probably you wouldn’t of really known that unless you had started from the beginning. Did you have a chance to check out anything else? This is my first request, therefore I didn’t really know how to present it. l also love to help people and due to my disability I am unable to do it myself. Thanks Donna

  2. Build you own computer, this is so cool because it is so amazing to be able to do just that and that is to build your own computer. Gone are the days when we had to have so much money to have some what do this for us, with website like yours this is so neat. Your post is well detailed and filled with so much good information. I am sure that you readers will love what you are sharing with them.

    • First of all Norman, Thank you for your kind comment. I do love helping people and if they get out of what I did than that would be tremendous. My heart is really being able to feel like you have done such a accomplishment in doing so. I have or I should say did use to love building them, but as life moves on I just hope more people are able to have the same experience. Once again Thank you so much Donna

  3. Very well written, I do believe I could follow these instructions to build this CPU. Job well done I probably will be back to see what we can do. Thank you Eileen

    • Thank you, Eileen I really take pride in my work. I wanted to make it completely fool proof, in saying that it could cost you a lot if you had made an error. I truly hope you do come back to visit me it would be my pleasure.
      Thanks again Donna

Leave a Reply to jschmidt5 Cancel reply

close

Enjoy this blog? Stay up to date with new posts.

Get new posts by email:
RSS
Follow by Email
Facebook
Facebook
Google+
Twitter
Visit Us
YOUTUBE
Pinterest
LinkedIn
Instagram
SNAPCHAT
WHATSAPP
SKYPE